Always Free Shipping—No Minimum Order. Contiguous U.S. orders only. Alaska and Hawaii excluded.
Pro Installer 400A Dual Bank Control Switch - MC10Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze.
- Tested to UL1107 ignition protection, CE
- Tinned copper 10mm (3/8 inch) studs
- Stainless steel washers and nuts
- Fiber reinforced plastics
- 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating)
- Waterproof to IP67
- Same interconnection height as Pro Installer
- Removable knob allows isolation during servicing
- 3 removable side plates for protection
- Industry standard 3.85 x 3.85 inch footprint
- For surface mounting only
- Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested
SpecificationsMounting: Surface, Rear or Front
Voltage: 48v DC (for 12-48v systems, both banks must be same voltage)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1, 1/2, Parallel, Off
Stud: 4x 10 mm (3.8")
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
The BEP Marine Pro Installer 400A Dual Bank Control Battery Switch provides intuitive control for separate house and engine battery banks, with House, Start, and Emergency Parallel functions in one switch. Designed for boats and vehicles with single engine and house battery banks, it helps support dedicated battery-bank use while allowing house loads such as lighting, stereo, refrigeration, and VHF radio to remain powered when the engine is electrically isolated.
The isolated-On position allows the engine to be disconnected during servicing while house loads remain available. Separating house and engine loads during normal operation also helps isolate sensitive electronics from starter motor voltage spikes. Front-access wiring, optimized cable access, removable side plates, and a shared interconnection height with the Pro Installer Busbar Range support compact surface-mounted installations.
Key Features
- Dual-bank control with House, Start, Emergency Parallel, and Off operation
- 400A continuous, 600A intermittent for 5 minutes, and 1500A cranking for 10 seconds when using cable sized to achieve the ratings
- Waterproof to IP67 and tested to UL1107 ignition protection and CE requirements
- Tinned copper 10 mm (3/8 inch) studs with stainless steel washers and nuts
- Removable knob for battery isolation during servicing and three removable side plates for protection
- Front or rear wiring access for surface mounting
Product Details
- Brand: BEP Marine
- Part Number: 772-DBC
- Voltage: 48V DC; for 12–48V systems, both banks must be the same voltage
- Dimensions: 3.85 x 3.85 x 3.62 inches
- Studs: Four 10 mm (3/8 inch) studs
- Construction: Fiber-reinforced plastics
- Mounting: Surface mount only; rear or front mounting access
- Ratings depend on cable size; smaller cable size reduces the amp rating
California Proposition 65 Warning
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Choose the BEP Marine Pro Installer Dual Bank Control Switch for organized, accessible control of engine and house battery banks.
Product summary: BEP Marine 400A Dual Bank Control Battery Switch with House, Start, and Emergency Parallel functions for 12–48V marine systems.
| Truck Freight: No |
| Oversized: No |
| Owners Manual Url: https://productimageserver.com/literature/ownersManual/58595OM.pdf |